Ford 3000 Tractor Specs and Years Built Parts OnlineNov 14, 2026 Share Ford built the 3000 utility tractor from 1965 to 1975, with a 3-cylinder engine in two sizes: 158 cu in gas or 175 cu in diesel. Nebraska tests measured 36.5 to 40.6 PTO horsepower, depending on fuel and transmission. To date your own tractor, read the production code stamped beside the serial number, just behind the starter. Key Points Years built: 1965 to 1975, in Highland Park, Michigan; Basildon, England; and Antwerp, Belgium. The Ford 3600 replaced it. Engines: Ford 3-cylinder gas (158 cu in, 2.6 L) or diesel (175 cu in, 2.9 L). Tested power: 36.49 to 40.63 PTO hp across eight Nebraska tractor tests. Transmissions: 4-speed (12-speed with the over/under auxiliary), 8-speed, 6-speed from 1970, and the 10-speed Select-O-Speed power shift. Hydraulics: open center at 2,500 psi, with a Category I hitch rated at 1,700 lbs at 24 in. Size: 75.8 in wheelbase, 3,700 lbs shipping weight, 4,185 lbs operating weight. Dating one: the model code, production code and serial number share one pad on the right side of the transmission. What Are the Ford 3000 Specs? The Ford 3000 is a two-wheel-drive utility tractor, and Ford's period brochures sold it as a "2-3 plow" machine. The figures below come from TractorData's compilation of Ford literature and from the Nebraska Tractor Test reports for the 3000. Specification Ford 3000 Production 1965 to 1975 Engine 3-cylinder gas, 158 cu in, or 3-cylinder diesel, 175 cu in PTO power (tested) 36.49 to 40.63 hp Drawbar power (tested) 29.76 to 35.43 hp Transmission 4-speed, 12-speed over/under, 8-speed, 6-speed or 10-speed Select-O-Speed Rear PTO 540 rpm; 540/1000 rpm with Select-O-Speed only Hydraulics Open center, 2,500 psi, 5 gpm pump 3-point hitch Category I, 1,700 lbs lift at 24 in Wheelbase 75.8 in Weight 3,700 lbs shipping, 4,185 lbs operating Fuel tank 13 gal Electrical 12 volt, negative ground, generator charging Steering is manual, with power steering as an option. Brakes are mechanical expanding shoe, a mechanical rear differential lock was optional, and the operator station is open, with a canvas cab offered as an option. What Engines Did the Ford 3000 Use? Both engines are Ford 3-cylinders with the same 4.20 in bore. The diesel uses a longer 4.20 in stroke, which is where its extra 17 cu in comes from. Engine spec Gas Diesel Displacement 158 cu in (2.6 L) 175 cu in (2.9 L) Bore x stroke 4.20 x 3.80 in 4.20 x 4.20 in Compression ratio 8:1 16.5:1 Rated speed 2,100 rpm 2,000 rpm Torque 123 lb-ft at 1,350 rpm 125.7 lb-ft at 1,150 rpm Air cleaner Dry Oil bath Battery 12 V, 80 Ah 12 V, 128 Ah Engine oil 8 qt 8 qt Firing order: 1-2-3 on both engines. A mid-run change: the I&T shop manual lists gas compression as 8.0:1 before July 20, 1968 and 7.8:1 after. Block stamping: the engine serial on the cylinder block includes a letter for the tractor (N for a 3000 built before July 20, 1968, C after) and a letter for the fuel (D diesel, G gasoline). That block stamping tells you the engine type at a glance, which helps when the decals are long gone. How Many Horsepower Is a Ford 3000? Between about 36 and 41 PTO horsepower, depending on fuel and transmission. The Nebraska Tractor Test Laboratory tested six versions in 1965 and two more in 1970, when the 6-speed arrived. Test (year) Fuel and transmission PTO hp Drawbar hp 881 (1965) Diesel, 8-speed 39.20 34.88 882 (1965) Diesel, Select-O-Speed 38.08 30.60 883 (1965) Diesel, 12-speed 39.46 35.43 885 (1965) Gas, Select-O-Speed 36.49 29.76 888 (1965) Gas, 8-speed 37.84 32.52 889 (1965) Gas, 12-speed 39.17 33.04 1051 (1970) Gas, 6-speed 38.33 31.15 1052 (1970) Diesel, 6-speed 40.63 34.96 TractorData also lists a 46.7 hp engine rating. That is an engine figure, not a measurement at the PTO, so compare tractors on the tested numbers above. Maximum pull in these tests ran from 4,622 to 5,208 lbs. Which Transmissions Were Offered on the Ford 3000? Four gearboxes were offered over the run, plus an auxiliary unit for the 4-speed. Which one your tractor has decides its speed range, its PTO type and several of its parts. 4-speed, with optional over/under: the auxiliary adds an overdrive and underdrive to each gear for 12 forward and 3 reverse. The tractor must be stopped to shift it. The I&T manual lists it for 2000 and 3000 tractors built before 1971. 8-speed: 8 forward and 2 reverse, with a four-speed selector on the left and a high-low range lever on the right. Stop to shift. 6-speed: 6 forward and 2 reverse, first offered on the 3000 in 1970. Select-O-Speed: a 10 forward, 2 reverse full power shift that changes gear while moving. It is the only 3000 transmission with a 1000 rpm PTO. Note which transmission you have before you order clutch, PTO or shift parts. Does a Ford 3000 Have a Live PTO? Some do. The PTO type follows the transmission, so two 3000s of the same year can behave differently. Transmission PTO type PTO speed 4-speed and 8-speed (standard) Transmission-driven, continuous running 540 rpm 12-speed over/under Live, standard 540 rpm 8-speed (option) Live, optional 540 rpm Select-O-Speed Independent 540 or 540/1000 rpm A transmission-driven PTO stops whenever you press the clutch, so the implement stops with the tractor. Ford's operator's handbook also sets a different clutch pedal free travel for each type: Transmission PTO (2000 and 3000): about 1.12 to 1.38 in (29 to 35 mm). Live PTO (2000 and 3000): about 1.38 to 1.63 in (35 to 41 mm). Standard PTO speed: 540 rpm, plus or minus 1 rpm. What Are the Ford 3000 Hydraulic and Hitch Specs? The 3000 runs an open-center system at 2,500 psi with a 5 gpm pump and 6.3 gallons of capacity. The hydraulics share oil with the rear axle, and Ford's handbook says to check that level with the lift arms raised. Pump: piston type, mounted on the left rear side of the engine and driven by a gear on the rear of the camshaft (I&T shop manual). Hitch: Category I three-point, rated at 1,700 lbs at 24 in. Draft control: on the 3000 the draft control spring senses the top link in tension or compression. The 2000 senses compression only. Power steering (option): 4.25 gpm at 600 psi. Filters: Ford's handbook calls for the hydraulic inlet and exhaust filters to be inspected every 2,400 hours. The I&T manual also notes that lift units with a production code date of September 16, 1969 or later carry design changes, one more reason to know your build date. How Big and Heavy Is a Ford 3000? The 3000 measures 127 in long on a 75.8 in wheelbase. Operating weight is 4,185 lbs, and fully ballasted it reaches 6,940 lbs. Dimension Inches Metric Wheelbase 75.8 in 192 cm Length 127 in 322 cm Width 64 in 162 cm Height to steering wheel 58 in 147 cm Height to hood 54 in 137 cm Height to exhaust 83 in 210 cm Ground clearance (transmission) 13.4 in 34 cm Front / rear tread 52 to 80 in / 52 to 76 in 132 to 203 cm / 132 to 193 cm Weight: 3,700 lbs shipping, 4,185 lbs operating, 6,940 lbs ballasted. Front tires: 5.50-16 or 6.00-16. Rear tires: 12.4-28, 13.6-28, 14.9-24 or 16.9-24. Factory loaders: TractorData lists the Ford 1200 (1,250 lbs lift at the pin, 114 in pin height), 771 (1,800 lbs, 97 in) and 772 (2,500 lbs, 100 in). Which Ford 3000 Variants and Relatives Should You Know? The 3000 name covers several chassis and three factories. Knowing which one you have narrows the parts search before you even read the serial. 3100: all-purpose version. 3300: vineyard version. 3310: narrow-chassis version. Plant prefixes: the serial number starts with A (Antwerp, Belgium), B (Basildon, England) or C (United States). Successor: the Ford 3600, built from 1975 to 1981. If you are coming from an older Ford, the 3000 is a different machine. The 1947 to 1952 Ford 8N used a 119.7 cu in 4-cylinder gas engine, according to TractorData, against the 3000's 3-cylinders. Our Ford 8N specs and parts guide covers that tractor. How Do I Tell What Year My Ford 3000 Is? Go to the right side of the tractor and find the implement mounting pad at the front corner of the transmission, directly behind the starter. The I&T shop manual says the numbers may be stamped on top of the pad, on its face, or partly on both. You will find three lines: Model code: in the decode published by Vintage Tractor Engineer, a 3000's model code starts with 3 (1965 to March 1968) or C (April 1968 on), and the fourth character is the fuel: 1 for diesel, 2 for gas. Production code: the build date, read as year, month, day and shift. Serial number: a plant letter followed by the production number. Production code part Means Codes First digit Year 5 = 1965 or 1975, 6 = 1966 through 9 = 1969, 0 = 1970 through 4 = 1974 Letter Month A Jan, B Feb, C Mar, D Apr, E May, F Jun, G Jul, H Aug, J Sep, K Oct, L Nov, M Dec (no I) Number Day 1 to 31 Last letter Shift A midnight, B day, C afternoon For example, 9G12C means July 12, 1969, afternoon shift. A 5 is the one ambiguous digit: it appears on both 1965 and 1975 tractors, so check the serial number to tell them apart. For US-built tractors (C prefix), TractorData publishes the first serial number of each year. Find the highest starting number that is lower than yours. Year First serial Year First serial 1965 C100000 1971 C292100 1966 C124200 1972 C327200 1967 C161300 1973 C367300 1968 C190200 1974 C405200 1969 C226000 1975 C450700 1970 C257600 A serial of C300000, for example, falls between C292100 and C327200, so it was built in 1971. These numbers cover US production only. For a B or A prefix tractor, use the production code instead. The engine has its own serial on the cylinder block pan rail, about mid-length, but an engine can be replaced over 50 years, so date the tractor from the transmission pad. Why Does the Build Date Matter When Ordering Parts? Ford changed parts during the run, and some of the changes are not interchangeable. The I&T shop manual for the 2000, 3000 and 4000 documents several by production date: Clutch, before October 1969: full cover with four release fingers and a full-circle fibrous disc. Clutch, October 1969 to August 1971: a ceramic button ("cerametallic") clutch with a three-finger cover. It is not interchangeable with earlier units, and fitting one to an earlier tractor means renewing the flywheel and clutch shaft too. Clutch, September 1971 on: a full-circle disc returned, but with square-cut splines that do not fit the early shaft. Engines: the tractor letter in the block stamping changed after July 19, 1968, and gas compression dropped from 8.0:1 to 7.8:1 at the same point. Hydraulic lift: design changes from lift unit production code date September 16, 1969. Ford's operator's handbook asks owners to quote identification numbers in full when ordering parts, and the reason is clear from this list. Send your model code, production code and serial to sales@partsonline.com and we will help you confirm the right part. It is the customer's responsibility to verify compatibility before purchasing. What Wears on a Ford 3000, and When Should It Be Serviced? The items Ford's operator's handbook asks you to service most often are the ones that wear: the air cleaner, fuel filters, engine oil and filter, grease points and the clutch adjustment. Its schedule for the 2000, 3000, 4000 and 5000: Interval What Ford's handbook calls for Daily or 10 hours Check engine oil, transmission, rear axle and coolant levels; check the oil-bath air cleaner cups 50 hours Clean and refill the oil-bath air cleaner; drain water from the fuel filters; grease all fittings; check clutch pedal free travel 300 hours Change engine oil and the oil filter element (every 150 hours below 10°F); check fan belt tension 600 hours Full air cleaner service; replace a single fuel filter element; check injectors and valve clearance; repack front wheel bearings 1,200 hours or annually Replace both elements on a double fuel filter; change transmission and rear axle oil 2,400 hours Have the hydraulic inlet and exhaust filters inspected In our catalog, the same fuel filter cartridge is cross-listed under dozens of Ford and New Holland part numbers, so you can search by the number printed on your old filter. Our aftermarket cartridge, which meets or exceeds OEM specifications, is listed under several of them, including Ford C5NE9176C, Ford D0NN9176B and New Holland 83937061. Each listing shows fitment for the Ford 3000. Match the number on your current filter, verify using your serial number, and bleed the fuel system after the change as the handbook directs. For the clutch, Ford's handbook says correct pedal free travel is essential for clutch life, so a pedal with no free play is worth fixing early. Replacing the clutch means splitting the tractor between the engine and transmission, so consult a certified mechanic for complex repairs. Block the wheels, lower any implement and stop the engine before working on the tractor. Browse our full range of Ford parts. Frequently Asked Questions How much is a Ford 3000 tractor worth today? It depends on configuration and condition: diesel or gas, transmission and PTO type, power steering, a loader, hours and overall condition all move the value. Compare recent sold results for 3000s with the same setup as yours. How many horsepower is a 3000 Ford tractor? Nebraska tests measured 36.49 to 40.63 PTO horsepower and 29.76 to 35.43 drawbar horsepower. The highest PTO figure came from a 1970 diesel with the 6-speed transmission. Was the Ford 3000 a good tractor? On the record, it was a capable 2-3 plow utility tractor: up to 40.63 PTO hp and 5,208 lbs of maximum pull in testing, with draft control that senses the top link in tension or compression. Parts are still widely cataloged, including fuel filters listed under Ford and New Holland numbers. Does a Ford 3000 have a live pto? Some do. A live PTO was standard with the 12-speed over/under and optional on the 8-speed, Select-O-Speed tractors have an independent PTO, and the others have a transmission-driven PTO. Is there a diesel Ford 3000? Yes. The diesel is a 175 cu in (2.9 L) 3-cylinder with 16.5:1 compression, offered alongside the 158 cu in gas engine. The fuel letter on the engine block (D for diesel) confirms which one you have. How much does a Ford 3000 weigh? About 3,700 lbs shipping weight and 4,185 lbs operating weight. With full ballast it reaches 6,940 lbs. Can a Ford 3000 run a loader? Yes. TractorData lists three Ford loaders for it: the 1200, 771 and 772, rated from 1,250 to 2,500 lbs of lift at the pin. Share Previous articleNext article Join Us A short sentence describing what someone will receive by subscribing Your email Subscribe100% free, Unsubscribe any time! Follow us