Bobcat E35 Specs: Dig Depth, Weight and Dimensions Parts OnlineNov 10, 2026 Share The current Bobcat E35 digs 121.2 inches (10 ft 1 in) deep, weighs 7,659 lb with the 24.8 hp engine or 7,893 lb with the 33.2 hp engine, and is 69.7 inches wide with zero tail swing. Those are R2-Series figures from Bobcat's brochure. The 2012 E35 differs, so match the specs to your generation. At a Glance Machine: Bobcat E35 compact (mini) excavator, 3.5-ton class, zero tail swing with the standard arm. Engine: 24.8 hp or 33.2 hp Tier 4 diesel on the R2-Series. The 2012 E35 has a 31.0 hp Kubota. Dig depth: 121.2 in with the standard arm, 133.0 in with the long arm and 153.2 in with the extendable arm (R2-Series). Size: about 190 in long, 69.7 in wide and 96.2 in tall with the cab. Hydraulics: 16.9 gpm of auxiliary flow at 2,987 psi on every generation covered here. Lift: 3,318 lb over the blade at ground level and 10 ft of reach. What Are the Bobcat E35's Key Specs? Bobcat sells the current R2-Series E35 with a choice of two engines. Apart from horsepower, weight, ground pressure and side-lift rating, the core numbers are the same for both. These figures come from Bobcat's compact excavator brochure (B-1857) for a standard-arm machine. Spec E35, 25 hp E35, 33 hp Horsepower 24.8 hp (18.5 kW) 33.2 hp (24.7 kW) Operating weight 7,659 lb 7,893 lb Max dig depth 121.2 in (10 ft 1 in) 121.2 in (10 ft 1 in) Reach at ground level 204.3 in (about 17 ft) 204.3 in (about 17 ft) Max dump height 133.1 in 133.1 in Bucket breakout force 7,284 lbf 7,284 lbf Arm breakout force 4,690 lbf 4,690 lbf Track width 69.7 in 69.7 in Tail swing Zero Zero Travel speed, low / high 1.6 / 2.9 mph 1.6 / 2.9 mph Auxiliary flow 16.9 gpm at 2,987 psi 16.9 gpm at 2,987 psi Fuel tank 13.7 gal 13.7 gal Ground pressure 4.6 psi 4.7 psi If you have seen 215.8 inches quoted as the E35's reach, that figure belongs to the long-arm machine. The standard arm reaches 204.3 inches at ground level. Which Bobcat E35 Generation Do You Have? The E35 name has covered more than one machine, and the specs moved with each change. Three generations are documented well enough to quote: Generation Engine Where the specs come from E35, S/N A93K11001 and above 1.8 L three-cylinder Kubota diesel, 31.0 hp Bobcat E35 Operation & Maintenance Manual 6987275 (2012) E35i (M-Series, Tier 4) 1.7 L naturally aspirated diesel, 24.8 hp Bobcat's launch announcement, as reported in the trade press R2-Series E35 24.8 hp or 33.2 hp Tier 4 diesel Bobcat compact excavator brochure B-1857 Bobcat introduced the E35i as a zero tail swing, 24.8 hp model with a direct-injection 1.7-liter engine and an optional extendable arm. We did not find a published weight or dig depth for it, so it stays out of the tables below. To tell which machine you have, read the serial number plate: our guide to finding the serial number on a Bobcat mini excavator shows where it is. The specifications section of your Operation & Maintenance Manual is written for a serial number range, so it is the authority for your machine. How Deep Can a Bobcat E35 Dig? A standard-arm R2-Series E35 digs 121.2 inches, or 10 feet 1 inch. Bobcat also offers a long arm and an extendable (telescoping) arm, and each adds depth and reach. Arm R2-Series dig depth 2012 E35 dig depth Standard arm 121.2 in 122.7 in Long arm 133.0 in 134.5 in Extendable arm, retracted Not listed 124.8 in Extendable arm, maximum 153.2 in 154.8 in (extended) Reach at ground level (R2-Series): 204.3 in standard, 215.8 in long arm, 235.1 in extendable arm. Max dump height (R2-Series): 133.1 in standard, 140.2 in long arm, 151.5 in extendable arm. 2012 E35, standard arm: 205.9 in of reach at ground level and 135.3 in of dump height. The small gaps between generations come straight from Bobcat's own documents, so quote the figure for your machine. The 2012 manual also says the extendable arm must be locked in the retracted position when lifting objects, transporting the machine or running hydraulic attachments. How Much Does a Bobcat E35 Weigh? An R2-Series E35 weighs 7,659 lb with the 24.8 hp engine and 7,893 lb with the 33.2 hp engine, both with the standard arm. The longer arms add several hundred pounds. Configuration 25 hp 33 hp Standard arm 7,659 lb 7,893 lb Long arm 8,362 lb 8,596 lb Extendable arm 8,590 lb 8,824 lb The 2012 manual starts from 7,468 lb for a canopy machine on rubber tracks with a 24-inch bucket, then lists what to add: Cab with heater: 267 lb Cab with HVAC: 309 lb Long arm with additional counterweight: 675 lb Extendable arm: 906 lb Count any extra buckets or attachments you carry when you check what your truck and trailer are rated to tow. What Are the Bobcat E35's Dimensions? The R2-Series E35 is about 190 inches long in travel position, 69.7 inches wide across the tracks and 96.2 inches tall with the cab. Bobcat's international spec sheet for the 33 hp model prints 4,823 mm and 2,443 mm, which match. Length, travel position: 190 in on the R2-Series. A 2012 machine measures 189.7 in with the standard arm and 190.3 in with the long or extendable arm. Width: 69.7 in across the tracks. Height: 96.2 in with the cab. Track shoes: 11.8 in (300 mm) rubber on the R2-Series. The 2012 manual lists 12.6 in rubber or 11.8 in steel. Boom swing: 75 degrees left and 55 degrees right, with a slew speed of 8.6 rpm. At 69.7 inches, the E35 is nearly 8 inches wider than the E32 (61.8 inches). Measure gates and side yards against that number before you book the job. Is the Bobcat E35 Zero Tail Swing? Yes, with the standard arm. The rear of the upper structure stays inside the track width as the house turns, so you can dig beside a wall or fence without the counterweight striking it. That changes with the arm options. Standard arm: zero tail swing. Long arm or extendable arm (R2-Series): Bobcat lists 3.2 in (81 mm) of tail overhang. The 2012 manual notes that the long arm comes with additional counterweight. E32 for comparison: conventional tail swing, with 13.4 in of overhang. If zero tail swing is the reason you chose an E35, check which arm is fitted before you work tight to a structure. How Much Can a Bobcat E35 Lift? Bobcat rates the R2-Series E35 at 3,318 lb over the blade at ground level and 10 ft of reach. Over the side, at the same point, the rating is 1,393 lb for the 25 hp model and 1,537 lb for the 33 hp model. Over the blade: 3,318 lb at ground level, 10 ft reach. Over the side: 1,393 lb (25 hp) or 1,537 lb (33 hp) at the same point. With a lifting clamp: the 2012 manual says lift capacity drops by 270 lb. Extendable arm: lock it retracted before lifting, per the 2012 manual. A lift rating holds only at the point where it is quoted. The 2012 manual carries separate lift charts for the standard arm, the standard arm with counterweight, the long arm and the extendable arm, so use the chart that matches your machine. What Engine and Hydraulics Does the E35 Have? The R2-Series E35 offers a 24.8 hp or 33.2 hp Tier 4 diesel, and Bobcat's brochure lists both as non-turbo. Bobcat's international spec sheet describes the 33 hp engine as a 1.8-liter, three-cylinder Bobcat engine. Bobcat's product copy says its compact excavators meet emissions standards without a diesel particulate filter (DPF). The 2012 E35 Operation & Maintenance Manual gives the earlier machine in detail: Engine: 1.8-liter (111.4 cu in) three-cylinder Kubota diesel, 31.0 hp SAE net at 2,400 rpm. Main pump: variable-displacement, load-sensing piston pump rated at 26.6 gpm. Auxiliary hydraulics: 16.9 gpm with a 2,987 psi relief. The second auxiliary circuit flows 5.4 gpm through the female coupler and 4.0 gpm through the male coupler. Main hydraulic filter: full flow, 3 micron synthetic media. The same manual calls for Bobcat hydraulic/hydrostatic fluid 6903117. Our guide to Bobcat hydraulic fluid explains which fluid each generation takes and what the 2012 E35 manual allows instead. What Are the E35's Fluid Capacities? Capacities barely changed between the 2012 machine and the R2-Series. The R2 hydraulic, coolant and engine oil figures below come from Bobcat's 33 hp international spec sheet, which prints metric values only. Fluid 2012 E35 R2-Series E35 Fuel tank 14 gal (53.1 L) 13.7 gal (51.9 L) Hydraulic system with reservoir 10.5 gal (39.7 L) 10.5 gal (39.7 L) Hydraulic reservoir only 2.5 gal (9.5 L) Not published Cooling system 2.1 gal (8.0 L) 2.1 gal (8.0 L) Engine oil with filter 5.5 qt (5.2 L) 5.5 qt (5.2 L) Travel motor, each 0.55 qt of SAE 90W Not published The 2012 manual prefers checking the hydraulic oil cold, against the cold mark on the tank decal. Filter and fluid change intervals for the E35 are in the hydraulic fluid guide linked above. Which Filters and Service Parts Fit the Bobcat E35? The 2012 E35 manual lists these maintenance part numbers for S/N A93K11001 and above. Each is available as an aftermarket replacement that meets or exceeds OEM specifications, and each listing shows fitment for the E35 and E35i: Primary hydraulic filter 6668819: Hydraulic Oil Filter, replacement for Bobcat 6668819 Hydraulic case drain filter 7009365: Hydraulic Oil Filter, replacement for Bobcat 7009365 Engine oil filter 6675517: Engine Oil Filter, replacement for Bobcat 6675517 Fuel filter 6667352: Fuel Filter with Water Separator, replaces Bobcat 6667352 Outer air filter 6672467 (inner 6672468): Outer Air Filter, replacement for Bobcat 6672467 On the 2012 machine, the tailgate opens the engine bay for the air cleaner, fuel filter and engine oil filter. The right side cover gives access to the hydraulic sight gauge and the primary hydraulic filter, and the case drain filter sits under the floor plate. Relieve hydraulic pressure and let the machine cool before you open the hydraulic system, and consult a certified mechanic for hydraulic repairs. Based on our catalog data, all five of these filter listings also show fitment for the E32 and E32i, so a mixed fleet can often share filter stock. Cab machines also need glass: our door glass replacing Bobcat 7251561 lists fitment for the E35 and E35i among other Bobcat excavators. Part numbers can change by serial number, and the 2012 list does not cover R2-Series machines, so verify yours before ordering. Send your serial number and the OEM number to sales@partsonline.com and we will check fitment, or browse every listing in Bobcat E35 parts. How Does the E35 Compare to the E32 and E50? Bobcat's R2-Series brochure lists the E35 beside the smaller E32 and the larger E42 and E50. Here is how they compare with standard arms: Model Operating weight Max dig depth Engine E32 7,403 lb 121.2 in 24.8 hp diesel E35 7,659 or 7,893 lb 121.2 in 24.8 or 33.2 hp diesel E42 9,830 lb 124.5 in 42.6 hp turbo diesel E50 11,357 lb 136.9 in 49.7 hp turbo diesel The E32 shares the E35's dig depth and 24.8 hp engine, but it has conventional tail swing and a narrower 61.8-inch track width. The E50, two sizes up, is heavier, digs deeper and is turbocharged, with 231.9 inches of reach at ground level. Our Bobcat E50 parts and service guide covers its maintenance. Frequently Asked Questions How much can an E35 lift? Bobcat rates the R2-Series E35 at 3,318 lb over the blade at ground level and 10 ft of reach. Over the side at the same point, it is 1,393 lb for the 25 hp model and 1,537 lb for the 33 hp model. Is the E35 a good excavator? It suits tight-access digging: zero tail swing with the standard arm, a 69.7-inch track width, 121.2 inches of dig depth and 16.9 gpm of auxiliary flow. If you need more depth or lift, look at the larger E42 or E50. How much does an E35 Bobcat excavator weigh? An R2-Series E35 weighs 7,659 lb with the 24.8 hp engine or 7,893 lb with the 33.2 hp engine, with the standard arm. The 2012 E35 manual lists 7,468 lb for a canopy machine on rubber tracks. What is the average price of a new Bobcat E35? Price depends on the engine, arm, cab and options, and dealer programs change it, so a quote from a Bobcat dealer is the reliable figure. We sell replacement parts for the E35, not machines. How much horsepower does a Bobcat E35 have? The R2-Series E35 has either 24.8 hp or 33.2 hp. The 2012 E35 has a 31.0 hp Kubota diesel, and the E35i was announced with 24.8 hp. How tall is a Bobcat E35? The R2-Series E35 is 96.2 inches tall with the cab. It is about 190 inches long in travel position and 69.7 inches wide. What is the difference between the Bobcat E32 and E35? The E35 has zero tail swing and a 69.7-inch track width, while the E32 has conventional tail swing (13.4 inches of overhang) and a 61.8-inch track width. Both dig 121.2 inches with the standard arm. Where can I find a Bobcat E35 spec sheet PDF? Bobcat's compact excavator brochure (B-1857) carries the R2-Series spec table. Your Operation & Maintenance Manual has a full specifications section written for your serial number range. Share Previous articleNext article Join Us A short sentence describing what someone will receive by subscribing Your email Subscribe100% free, Unsubscribe any time! Follow us