CAT Oil, Fuel and Air Filter Cross Reference Guide Parts OnlineNov 19, 2026 Share CAT's B3 skid steer manual covers one family of loaders with two different engines, the C2.2 and the C3.4, which is why CAT filters are matched by engine and serial number rather than by model alone. This CAT oil filter cross reference lists the oil, fuel and air filter numbers we carry for CAT skid steers, track loaders and mini excavators, with change intervals from CAT's own manuals. Key Points Start with the number on your old filter or in your machine's parts book. CAT prints numbers with a dash (377-6969); our listings drop it (3776969). Two oil filter numbers cover most CAT loaders in our catalog: 1504140, listed for machines such as the 226B and 232D, and 3776969, listed for D3-series loaders such as the 242D3 and 299D3 plus C-series machines such as the 262C2. Small mini excavators differ: our 3769707 listing shows fitment for the 301.4C, 301.7D, 302.2D, 302.4D and 302.7D. Air filters come in pairs: a primary (outer) element and a secondary (inner or safety) element, such as 1106326 and 1106331 on loaders like the 262D and 299D3. Intervals vary by machine: CAT's B3 and D-Series loader manuals set oil and filter changes at 500 service hours or one year under listed conditions. The 300.9D mini excavator manual says every 250 hours. How Do I Find the Right CAT Filter Number? The fastest route is the filter you are replacing, since the part number is usually printed on the canister or the element. If the label is gone, use the parts book for your machine's serial number. CAT's own manuals split filter service by engine and serial range, not just by model. Old filter: read the number off the can or the element before you throw it away. Parts book by serial: the serial prefix (for example JXM for some 216B3 loaders) ties your machine to the right engine and filter list. Model and suffix: a 242B and a 242D3 are different machines, and our listings give them different oil filters. Our guide to CAT skid steer models explains how to read the suffix. Number format: CAT writes 377-6969; many catalogs, including ours, search it as 3776969. Both mean the same part. Once you have a number, the tables below show what our listings carry under it and which machines each listing names. Which CAT Oil Filter Fits My Skid Steer or Track Loader? Our catalog splits CAT compact loaders into two main engine oil filter groups, and the split follows the engine. The 1504140 listing names CAT C1.5 through C2.2 engines. The 3776969 listing names the C3.3B, C3.4 and C3.8 engines, among others, and CAT's parts site lists 377-6969 as a Standard Efficiency engine oil filter. OEM number (as listed) Listing shows fitment for Our replacement 1504140 Skid steers 216, 216B to 216B3, 226, 226B to 226B3, 226D, 226 D3, 228, 232, 232D, 232 D3, 236, 242, 242B, 242B2, 246, 248, 252, 262. Track loaders 239D, 239 D3, 247, 247B, 247B2, 249D, 249 D3, 257, 257B to 257B3, 267, 277, 287 Engine oil filter replacing CAT 1504140 3776969 Skid steers 236D3, 242D3, 246C, 246D3, 256C, 262C2, 272C, 272D3, 272D3XE. Track loaders 257D3, 259D3, 279C2, 279D3, 287C, 289C2, 289D3, 297C, 299D3, 299D3XE Engine oil filter replacing CAT 3776969 CAT's own manuals show why the engine matters. The B3 manual for the 216B3 to 259B3 carries separate service illustrations for the C2.2 and C3.4 engines, and the D-Series manual shows the C2.2, C3.3B and C3.8. If your loader is not in either row, or the suffix is unclear, send us the serial number and the number on your old filter. It is the customer's responsibility to verify compatibility before ordering. Which Oil Filter Fits a CAT Mini Excavator? CAT mini excavators split across three oil filter listings in our catalog. Our guide to CAT mini excavator sizes and models helps if you are unsure which machine you have. OEM number (as listed) Listing shows fitment for Our replacement 3769707 301.4C, 301.7D, 302.2D, 302.4D, 302.7D Engine oil filter replacing CAT 3769707 1504140 301.5, 301.6, 301.7CR, 301.8, 302CR, 302.7CR, 303CR, 305CR Same listing as the loader table 3776969 301.7D, 306 CR, 306E, 307E, 308E CR, 308E SR, 309 CR Same listing as the loader table One catch from our own catalog: the 301.7D appears in both the 3769707 and 3776969 listings. When two numbers show up for one model, the filter on your machine or the parts book for your serial number settles it. Email the number to sales@partsonline.com and we will check it for you. Which CAT Air Filters Fit Compact Loaders and Mini Excavators? CAT's B3 and D-Series manuals list two engine air filter elements, a primary and a secondary, and service them on separate rules. Order them as a matched pair for your machine. Machines (as our listings show) Primary element Secondary element Skid steers 216B, 216B2, 216B3, 226B, 226B2, 226B3, 242B, 242B2. Track loaders 247B, 247B2, 257B, 257B2 1547108 or 2942519 1232368 or 2942520 Many skid steers and track loaders, including the 236D, 246C, 262D, 272D3, 259D3, 279D3, 289D3 and 299D3 (full list on the listing) 1106326 1106331 Mini excavators 301.6, 301.8, 302.5, 303.5, 303CCR, 304.5, 304C 1213661 or 1467472 1467473 or 2483865 Mini excavators 301.4C, 301.7D, 302.7D 1394834 or 1555410 2349828 On the large loader pair, our listings title both parts "Air Filter Element." 1106326 is the larger outer element, and CAT's parts site describes 110-6331 as a secondary engine air filter. See our air filter element replacing CAT 1106326 and the matching inner element replacing CAT 1106331. Which CAT Fuel Filters Fit Compact Equipment? CAT's B3 and D-Series loader manuals list two fuel filters: an in-line fuel filter and a primary filter that doubles as the water separator. The B3 manual describes the separator element plainly: "This unit has a dual purpose. The element serves as a water separator and a fuel filter." Mini excavators: our fuel filter element replacing CAT 1835446 shows fitment for the 300.9D, 301.7D, 301.7 D CR, 302.4D, 302.5C, 303.5 C/CR, 303CR, 304 C/CR, 305.5CR, 305CCR and 305CR. Our 2337761 and 3727361 listings show the same fitment. Skid steers and track loaders: fuel filter numbers change with the engine, so take the number off your current filter or the parts book and send it to us. We list CAT fuel filters by OEM number. In-line filter direction: the B3 manual says to make sure "the arrow on the filter points upward" when you fit a new one. The same manual says to replace the in-line filter early if its screen is more than half blocked or engine performance is poor. How Often Should CAT Filters Be Changed? The intervals below come straight from CAT's Operation and Maintenance Manuals, which add that machines working in severe conditions may need more frequent service. Machine (manual) Engine oil and filter Fuel filters Air filters 216B3 to 259B3 loaders (SEBU8495) 500 h or 1 year* 500 h or 6 months, both filters When the restriction indicator lights; primary replaced at least yearly D and D2-Series loaders (SEBU9084) 500 h or 1 year* 500 h, both filters 500 h, primary and secondary 300.9D mini excavator (SEBU8740) First at 50 h, then every 250 h First at 50 h, then every 500 h 500 h *The 500-hour interval applies only when the manual's conditions are met, which include the recommended engine oil, Cat filters, and an altitude no higher than 7,545 ft (2,300 m). The D-Series manual calls for 250 hours or 6 months when any of those is not met, and it lists "Cat filters are not used" as one of them. The B3 manual drops to 250 hours above 7,545 ft or with fuel sulfur between 0.50% and 1.00%, and to 125 hours above 1.00%. Drain the water separator daily: both loader manuals list it as an every-10-hours or daily item. Air filter cleaning limit: the B3 manual says a properly cleaned and inspected primary element can be used up to three times, and the secondary is replaced when the primary is cleaned for the third time. The secondary is never reused. What Should Match When You Cross-Reference a CAT Filter? A part number match gets you close, and the physical details confirm it. These are the features to compare between your old filter and the replacement: Thread size on the center bore, which decides whether the filter threads onto the head at all. Gasket diameter, since the seal must land on the filter base. Height and outer diameter, which matter in tight engine bays. Valves: an anti-drainback valve and a bypass valve, if the original has them. Efficiency grade: CAT sells engine oil filters in Standard, Advanced and Ultra High Efficiency versions, according to a Cat dealer's filter guide. The same checks apply on any brand. Our Bobcat oil filter cross-reference guide walks through them for Bobcat numbers. Where Are the Filters on a CAT Skid Steer? CAT's B3 manual gives these locations for the 216B3 to 259B3. Other series place things differently, so treat this as a guide for B3 machines and check your own manual for the rest. Engine air filter: left side of the engine compartment on machines with the C2.2 engine, right side on machines with the C3.4. Fuel filter and water separator: left side of the engine compartment. Engine oil: the oil service is done with the engine access door open and the radiator tilted up. The crankcase drain is on the right side of the oil pan. Before you work in the engine compartment, park on level ground, lower the lift arms or install the lift arm support, stop the engine, and follow the access steps in your manual. How Do I Replace a CAT Oil Filter? This is the procedure from CAT's B3 and D-Series manuals. Hot oil and hot components can cause burns, so let the engine cool enough to handle safely. Open the engine access door. On B3 loaders, tilt the radiator upward. Drain the crankcase into a suitable container. The drain is on the right side of the oil pan. Remove the old filter with a filter wrench and keep it for inspection. Apply a thin film of clean engine oil to the sealing surface of the new filter. Install the filter hand tight until the seal contacts the base, and note where the index marks sit. CAT's marks are spaced 90 degrees, or a quarter turn, apart. Tighten the filter to the instructions printed on it. The D-Series manual adds: "For non-Cat filters, use the instructions that are provided with the filter." Fill the crankcase with the oil your manual specifies, start the engine, let it warm and check for leaks. Stop the engine, let the oil drain back, and top up to the FULL mark without going over it. Dispose of the used oil and filter according to local regulations. If the filter will not come off or the threads look damaged, consult a certified mechanic. What Can a Used Oil Filter Tell You? CAT's manuals include a step most owners skip: cut the old filter open with a filter cutter, spread the pleats and look for metal. A small amount of debris can come from normal friction and wear. A large amount can point to a failure in progress. Use a magnet to separate ferrous from nonferrous metal. Ferrous metal: CAT links it to wear on steel and cast iron parts. Nonferrous metal: CAT links it to aluminum parts such as main bearings, rod bearings or turbocharger bearings. If you find more than a light trace, have a certified mechanic check the engine or arrange an oil analysis. Browse our full range of CAT parts for filters by OEM number, and send your serial number to sales@partsonline.com if you want us to confirm a match. Frequently Asked Questions What are two types of oil filters? Full-flow and bypass. A full-flow filter cleans all of the oil before it returns to the engine, while a bypass filter treats a small share of the flow, about 10% in one filter maker's guidance, and returns it to the sump. Can you run a cat oil filter on a 6.7 powerstroke? Any filter fits only if its thread, gasket, size and valve settings match what the engine's maker specifies. Our CAT filter listings show fitment for CAT machines only, so check the filter number in the truck's own manual first. How do I clean my oil filter? You do not clean a spin-on oil filter. CAT's schedules replace it with every oil change, and its manuals recommend cutting the old one open to check the pleats for metal. What is the cross reference for a CAT oil filter? It depends on the engine. In our catalog, 1504140 is listed for loaders such as the 226B and 232D, 3776969 for D3-series loaders such as the 299D3, and 3769707 for small mini excavators such as the 302.7D. How often should a CAT oil filter be replaced? CAT's B3 and D-Series loader manuals change the oil and filter together every 500 service hours or one year when the manual's conditions are met, and the D-Series manual shortens that to 250 hours or 6 months when they are not. The 300.9D mini excavator manual calls for every 250 hours after a first change at 50. What is the best CAT oil filter? The right one is the filter that matches your engine's number and specs. CAT sells oil filters in efficiency grades such as Standard and Advanced Efficiency, so match the type your machine calls for and verify fitment with your serial number. Share Next article Join Us A short sentence describing what someone will receive by subscribing Your email Subscribe100% free, Unsubscribe any time! Follow us